Dec 13, 2016 · Chromium (Cr) 16.00 18.00 Nickel (Ni) 6.00 8.00 Nitrogen (N) 0.10 max. Iron (Fe) Balance AVAILABLE FORMS AK Steel produces Type 301 Stainless Steel in thicknesses from 0.01 0.187 in. (0.25 4.75 mm) max. and widths up to 60 in. (1524 mm). For other thicknesses and widths, please contact your AK Steel sales representative.
50% Nickel and 50% Chromium MaterialMar 28, 2007 · Again, this is a pure astenitic material containing approximately 60-63% nickel and around 20-25% chromium and 6% moly. Of course, the most important thing when welding any stainless steel is the ability to start out CLEAN.
Where ellipsesappear . in this table, there is no minimum and analysis for the element need notbe determined or reported.TABLE 2 Room Temperature Tensile and Charpy RequirementsA50 Cr-50 Ni 60 Cr-40 Ni 50 Cr-50 Ni-CbTensile strength, min, ksi MPa 80 550 110 760 80 550Yield point, min, ksi MPa 50 340 85 590 50 345Elongation in 2 in. 50 mm,min, 5
ASTM F75 ASTM F Cobalt Chrome Alloy 75 CoCr Alloyaero- and land-based gas turbines. While vacuum cast nickel alloys predominate in the hot sections of modern aero turbine engines, cobalt alloys are routinely specified for particularly demanding applications such as fuel nozzles and vanes for indus-trial gas turbines. Arcam ASTM F75 is a non-magnetic CoCrMo alloy exhibiting high
ASTM-A403-A403M- Standard-Specification-for- 1.6 This specication does not apply to cast steel ttings. Pressure-Containing Parts A743/A743M Specication for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application A744/A744M Specication for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service 5.9 Grade CR ttings
Sep 24, 2015 · Gray Iron ASTM A48 Class 30. The Myth of Chrome White Iron and Hardness. How to Heat Treat ASTM A532 High Chrome White Iron. An Oil Sands Success Story with ASTM A532. The Differences Between Ni-Hard and Chrome White Iron. The Myths of Chrome White Iron Brittleness. Austenitic Ductile Iron ASTM A439 Grade D2 58-30-8
Chemical Specification of Commonly Cast - Aloke Alloys60 Ni 40 CrNb--ASTM A560 Gr 60/40 Nb-----For heat resisting and elevated temperature corrosion resistance application such as tube hangers. CY-40 (70Ni15Cr)--ASTM A494 Gr CY-40:0.35 - 0.45:Balance:14.0 - 17.0-3.0 max:1.5 max:11.0 Fe max:Frequently used for elevated temperature fittings in conjunction with Inconel.
Chromium Alloys - an overview ScienceDirect TopicsThe biologic reactivity of released nickel from CoNiCr alloys is a cause for concern under static conditions, and due to their poor frictional (wear) properties CoNiCr alloys are also inappropriate for use in articulating components. Therefore the dominant implant alloy used for total joint components is CoCrMo (ASTM F75).
cw12mw equivalent, A494 Gr CW12MW SA 0.12 1.00 1.00 bal 15.5-17.5 16.0-18.0 72 40 4 A494 Gr M35-1 as-cast 0.35 1.50 2.00 bal 65 25 25 A297 Gr HT 330 as-cast .35-.75 2.00 2.50 33.0-37.0 15.0-19.0 0.50 65 4 Eagle Alloy, Inc. is capable of producing any steel specifications. The above is a representative sample of alloys produced. MATERIAL SPECIFICATIONS
HEAT AND CORROSION RESISTANT CASTINGS - Nickel-Chromium-Iron Alloys (HN, HP, HT, HU, HW, HX) No. Ni Cr C Mn max Si max Mo max Other HA 8-10Cr A217 8-10 0.20 max 0.35-0.65 1.00 0.90-1.20 Fe bal HC 28Cr A297 446 J92605 4 max 26-30 0.50 max 1.00 2.00 0.5 Fe bal Nickel Nickel is present in cast heat-resistant alloys in amounts up to 70%. Its principal function is to
High-Strength Low-Alloy SteelsSmall quantities of chromium, nickel, molybdenum, copper, nitrogen, vanadium, niobium, titanium, and grade designation C Mn P S Si Cr Ni Cu V Other plate thicker than 40 mm (1 to 5 in.), ASTM A 841 specifies manganese contents of 1.00 to 1.60%.
ASTM SAE ASME Heat Treatment C Mn Si Ni Cr Mo Tensile ksi Yield ksi % Elong % RA A494 Gr CW12MW SA 0.12 1.00 1.00 bal 15.5-17.5 16.0-18.0 72 40 4 A494 Gr M35-1 as-cast 0.35 1.50 2.00 bal 65 25 25 Corrosion Resistant Iron-Chromium-Nickel Alloy Castings for General Application.
Nickel Alloy Steel Castings Peninsula Alloy IncCommon Name ASTM # Grade Approximate Equivalent; Chromium-Nickel Alloys:A560:50 Cr-50 Ni:Chromium-Nickel Alloys:A560:60 Cr-40 Ni:Chromium-Nickel Alloys:A560
SAE steel gradesType 439ferritic grade, a higher grade version of 409 used for catalytic converter exhaust sections. Increased chromium for improved high temperature corrosion/oxidation resistance. Type 440a higher grade of cutlery steel, with more carbon, allowing for much
The most common stainless steel is the 304 grade with 8% nickel and 18% chromium and the balance iron. This is used for such common items as spoons and forks, saucepans and kitchen sinks. Where extra corrosion resistance is required, such as for roofing in marine applications, type 316 is used.ASTM A560 / A560M - 12(2018) Standard Specification for 1.1 This specification covers chromium-nickel alloy castings intended for heat-resisting and elevated-temperature corrosion applications, such as structural members, containers, supports, hangers, spacers, and the like, in corrosive environments up to 2000 °F [1090 °C].